FORE:The most effectual means of securing a uniform effect from a tempering bath is by violent agitation, either of the bath or the piece; this also adds to the rapidity of cooling.
Sed ut perspiciatis unde omnis iste natus error sit voluptatem accusantium doloremque laudantium
FORE:She shook her head and smiled as she held out three pounds and three shillings.A great share of the handling about an engineering establishment is avoided, if material can be stored and received on a higher level than the working floors; if, for instance, coal, iron, and sand is received from railway cars at an elevation sufficient to allow it to be deposited where it is stored by gravity, it is equivalent to saving the power and expense required to raise the material to such a height, or move it and pile it up, which amounts to the same thing in the end. It is not proposed to follow the details [74] of shop arrangement, farther than to furnish a clue to some of the general principles that should be regarded in devising plans of arrangement. Such principles are much more to be relied upon than even experience in suggesting the arrangement of shops, because all experience must be gained in connection with special local conditions, which often warp and prejudice the judgment, and lead to error in forming plans under circumstances different from those where the experience was gained.
Sed ut perspiciatis unde omnis iste natus error sit voluptatem accusantium doloremque laudantium
FORE:I could not help myself, but also pressed through the Germans, as I wanted to exchange a few words with the Belgians. This was possible for a very few moments only, in which they told me that they had been firing night and day in order to harass the Germans who crossed the river, but they had to yield at the end, when the Germans put Belgian civilians in front of themselves when attacking the fort.Screw-cutting machines may be divided into modifications as follows:(1) Machines with running dies mounted in what is called the head; (2) Machines with fixed dies, in which motion is given to the rod or blank to be threaded; (3) Machines with expanding dies which open and release the screws when finished without running back; (4) Machines with solid dies, in which the screws have to be withdrawn by changing the motion of the driving gearing; making in all four different types.
Sed ut perspiciatis unde omnis iste natus error sit voluptatem accusantium doloremque laudantium
At vero eos et accusamus et iusto odio dignissimos ducimus qui blanditiis praesentium voluptatum deleniti atque corrupti quos dolores et quas molestias excepturi sint occaecati cupiditate non provident,similique sunt in culpa qui officia deserunt mollitia
At vero eos et accusamus et iusto odio dignissimos ducimus qui blanditiis praesentium voluptatum deleniti atque corrupti quos dolores.
At vero eos et accusamus et iusto odio dignissimos ducimus qui blanditiis praesentium voluptatum deleniti atque corrupti quos dolores.
At vero eos et accusamus et iusto odio dignissimos ducimus qui blanditiis praesentium voluptatum deleniti atque corrupti quos dolores.
At vero eos et accusamus et iusto odio dignissimos ducimus qui blanditiis praesentium voluptatum deleniti.
At vero eos et accusamus et iusto odio dignissimos ducimus qui blanditiis praesentium voluptatum deleniti.
At vero eos et accusamus et iusto odio dignissimos ducimus qui blanditiis praesentium voluptatum deleniti.
At vero eos et accusamus et iusto odio dignissimos ducimus qui blanditiis praesentium voluptatum deleniti.
At vero eos et accusamus et iusto odio dignissimos ducimus qui blanditiis praesentium voluptatum deleniti.
At vero eos et accusamus et iusto odio dignissimos ducimus qui blanditiis praesentium voluptatum deleniti.
On the other hand, we denounce with righteous indignation and dislike men who are so beguiled and demoralized by the charms of pleasure of the moment, so blinded by desire, that they cannot foresee
78212
THREE:In cutting screws it is best not to refer to that mistaken convenience called a wheel list, usually stamped on some part of engine lathes to aid in selecting wheels. A screw to [127] be cut is to the lead screw on a lathe as the wheel on the screw is to the wheel on the spindle, and every workman should be familiar with so simple a matter as computing wheels for screw cutting, when there is but one train of wheels. Wheels for screw cutting may be computed not only quite as soon as read from an index, but the advantage of being familiar with wheel changes is very important in other cases, and frequently such combinations have to be made when there is not an index at hand.